Fpr-1010 cisco usb driver download
Facing the rear of the chassis, the LEDs are located on the top left edge facing the front of the chassis, they are in the back right corner of the top. The network port LEDs are at the top sides of each network port. The following figure shows the status LEDs on the rear panel and on the cover of the chassis. The following figure shows all of the LEDs on the rear panel of the Firepower and describes their states.
Green, flashing slowly twice in 5 seconds —Cloud connected. Green—Failover pair operating normally. The LED is green always unless the chassis in a high availability pair. Amber—When the chassis is in a high availability pair, the LED is amber for the standby unit. Not including any PoE devices connected to the chassis. The following table lists the field-replaceable PIDs associated with the Firepower The spare components are ones that you can order and replace yourself.
If any internal components fail, you must get a return material authorization RMA for the entire chassis. See the Cisco Returns Portal for more information. Each power supply has a separate power cord. Standard power cords or jumper power cords are available for connection to the security appliance. The jumper power cords for use in racks are available as an optional alternative to the standard power cords. If you do not order the optional power cord with the system, you are responsible for selecting the appropriate power cord for the product.
Using a incompatible power cord with this product may result in electrical safety hazard. Orders delivered to Argentina, Brazil, and Japan must have the appropriate power cord ordered with the system. Only the approved power cords or jumper power cords provided with the chassis are supported. Skip to content Skip to search Skip to footer. Book Contents Book Contents. Find Matches in This Book. PDF - Complete Book 7. Updated: November 22, Chapter: Overview. The following figure shows the Cisco Firepower Figure 1.
Cisco Firepower The following table lists the features for the Firepower Table 1. Lock slot Accepts a standard Kensington T-bar locking mechanism for securing the chassis Reset button A small recessed button that if pressed for longer than three seconds resets the chassis to its default state following the next reboot.
Power switch No System power is controlled by the power cord; there is no power button. Power cord socket The chassis is powered on when you plug in the AC power supply. Note Use the power supply part number that shipped with the chassis. Storage One GB M. Rubber feet Four rubber feet on the bottom of the chassis Note The rubber feet are needed for proper cooling. Do not remove them.
Only one console port can be active at a time. The console ports do not have any hardware flow control. You can use the CLI to configure the chassis through either serial console port by using a terminal server or a terminal emulation program on a computer. Package Contents The following figure shows the package contents for the Firepower Figure 2.
The following figure shows the QR code sticker. Figure 3. Figure 4. Firepower QR Code Sticker 1 QR code sticker — Serial Number Location You can view the serial number and additional model information on the compliance label located on the bottom of the chassis. The following figure shows a sample compliance label. Figure 5.
Figure 6. Figure 7. Figure 8. Figure 9. Green—Power supply on. Green, flashing quickly—System is booting up. Green—Normal system function. Amber—Critical alarm indicating one or more of the following: Major failure of a hardware or software component.
Over-temperature condition. Power voltage outside the tolerance range. Green and amber, flashing—Cloud connection failure. Green—Cloud disconnected. Link status L : Off—No link, or port is not in use. Green—Link established. Green, flashing—Link activity. Table 2. Table 3. Note Only the approved power cords or jumper power cords provided with the chassis are supported. The following power cords are supported. Figure Was this Document Helpful? Yes No Feedback. Certified on FTD 6. Form factor.
Desktop mount Wall mount Cisco part number Rack mount Cisco part number Side-to-side No fan. Boot partition. L2 switch. Management port. Console port. To uninstall the driver, use the Add Remove Programs utility or the Setup-exe program. Note Disconnect the console terminal before uninstalling the driver.
Note The download site redirects you to a router download section where the drivers are also applicable to Firepower products. Step 2 Install the driver. Figure 1. Step 5 Follow the instructions to complete the driver installation. Step 6 To communicate with the chassis, start a terminal emulator application.
This software should be configured with the following parameters: baud 8 data bits no parity 1 stop bit no flow control Connect to the Console Port with Mac OS X Follow these steps to connect a Mac OS X system USB port to the console using the built-in OS X Terminal utility, or alternatively you can use a separate terminal emulator application. Procedure Step 1 Open the Linux Terminal window. Was this Document Helpful? Yes No Feedback. Disconnect the console terminal before uninstalling the driver.
Install the driver. Console Port Connection 1.
0コメント